| XU08012 INA Slewing Ring Bearings | F:504 mm; C:368 mm; D1 ≈:562.3 mm; Fatigue load limit Pu:1270 kN; r1,2 min.:12 mm; r3,4 min.:3 mm; Basic static load rating C0:14600 kN; K:9 mm; b:16.7 mm; B:368 mm; Design variant/feature:BC4.12/W33G; D:600 mm; α:20 °; Basic dynamic load rating C:5500 kN; d:475 mm; Calculation factor kr:500; Mass bearing:235 kg; |
| RKS.221300101001 SKF Slewing Ring Bearings | Sealed Speed Rating n3:1800 rpm; D:190.0000 mm; Basic Static Radial Load Rating Co:180000 N; B:65.10 mm; Fillet Radius ra:2.00 mm; Oil Speed Rating n2:2800 rpm; d:105.000 mm; Grease Speed Rating n1:1800 rpm; Accessories:Two Seals & Snap-Rin; Basic Dynamic Radial Load Rating C:186000 N; |
| XSU140644 INA Slewing Ring Bearings | L:419.1 mm; RG:3/8 NPT; Appropriate attachment bolt size G:0.75 in; R1:67.866 mm; P60°:149 kN; H:239.316 mm; End plug (suffix Y):EPR 13; J min.:320.675 mm; H2:50.8 mm; PG:1/4 NPT; S:4.763 mm; P180°:60.9 kN; Taconite seal:TER 557; H1:125.425 mm; N1:22.225 mm; P120°:55.6 kN; Mass pillow block:33.1 kg; P150°:50.7 kN; Ca:62.789 mm; A2:231.775 mm; |
| RKS.061.20.0644 SKF Slewing Ring Bearings | A2:273.05 mm; H2:60.325 mm; Initial grease fill:765.45 g; Max. speed for Taconite seal:775 r/min; J min.:371.475 mm; P90°:113 kN; Pa:16.7 kN; J1:82.55 mm; H:287.337 mm; Cap bolt, SAE grade:8; ba:48.419 mm; H1:152.4 mm; Ca:89.789 mm; Stabilizing ring:2 x SR-1622; L:466.725 mm; R1:79.375 mm; P150°:68.1 kN; da:96.838 mm; RG:1/2 NPT; Da:240 mm; |
| VSI200644-N INA Slewing Ring Bearings | Pa:14 kN; P150°:28.9 kN; A2:233.363 mm; Initial grease fill:181.44 g; L:361.95 mm; Max. speed for Taconite seal:1150 r/min; P180°:34.7 kN; J min.:269.875 mm; H1:107.95 mm; PG:1/8 NPT; Mass pillow block:29.9 kg; R2:26.988 mm; S:4.763 mm; R1:63.5 mm; End plug (suffix Y):EPR 8; ba:46.038 mm; Da:170 mm; Housing:SAF 616; H2:44.45 mm; h:42.862 mm; |
| HT10-60E1Z Kaydon Slewing Ring Bearings | da max.:65.8 mm; B2 ≈:40 mm; Da min.:83.1 mm; Basic dynamic load rating C:116 kN; D:100 mm; Mass bearing + sleeve:0.95 kg; Fatigue load limit Pu:13.4 kN; s1 max.:8.6 mm; d1:50 mm; G:M 60x2; Ca min.:0.3 mm; ra max.:1.5 mm; Da max.:91 mm; da min.:60.6 mm; d2 ≈:65.8 mm; r1,2 min.:1.5 mm; Operating clearance factor k2:0.133; B:25 mm; G1:7 mm; B1:37 mm; |
| RKS.060.20.0844 SKF Slewing Ring Bearings | Sealed Speed Rating n3:1600 rpm; Oil Speed Rating Open/Shielded n2:2900 rpm; D:290.0000 mm; B:65.00 mm; Fillet Radius ra:3.00 mm; Accessories:Two Seals; d:105.000 mm; Basic Dynamic Radial Load Rating C:247000 N; Basic Static Radial Load Rating Co:228000 N; Grease Speed Rating Open/Shielded n1:2400 rpm; |
| VA250309-N INA Slewing Ring Bearings | N1:25.4 mm; Ca:55.804 mm; Labyrinth ring:2 x LOR 103; P180°:55.6 kN; L:387.35 mm; Cap bolt recommended tightening torque:203.4 N·m; Cap bolt, SAE grade:5; RG:3/8 NPT; J max.:333.375 mm; A2:152.797 mm; R2:30.163 mm; Appropriate attachment bolt size G:0.875 in; Cap bolt:2 x 3/4-10 UNC; Max. speed for PosiTrac Plus seal:1650 r/min; Da:180 mm; Pa:13.8 kN; P60°:136 kN; R1:58.737 mm; Initial grease fill:181.44 g; |
| 16370001 Kaydon Slewing Ring Bearings | B1:206 mm; Static (Cor):17850 ; Dynamic (Cr):6568.8 kN; D:1180 mm; Bearing designation:PLC 512-60 ; d:850 mm; Pu:1086.140 kg; Weight:880 ; B:331 mm; |
| RKS.221091 SKF Slewing Ring Bearings | J min.:209.55 mm; H1:69.85 mm; Basic dynamic load rating C:148 kN; H2:41.275 mm; J max.:222.25 mm; S:0.794 mm; A:73.025 mm; H:144.463 mm; B:85.725 mm; Attachment bolt diameter G:15.875 mm; s:31.75 mm; L:266.7 mm; Limiting speed:1100 r/min; A1:91.281 mm; da:61.913 mm; d2:101.6 mm; Mass bearing unit:8.39 kg; |
| 16351001 Kaydon Slewing Ring Bearings | A2:209.55 mm; Appropriate attachment bolt size G:0.625 in; Cap bolt:2 x 5/8-11 UNC; Da:140 mm; H:167.481 mm; Initial grease fill:87.885 g; da:53.975 mm; RG:3/8 NPT; Cap bolt, SAE grade:8; J1:53.975 mm; P120°:21.8 kN; H1:88.9 mm; R1:46.038 mm; J max.:279.4 mm; Mass pillow block:18.1 kg; J min.:244.475 mm; P150°:19.6 kN; H2:31.75 mm; Taconite seal:TER 31; Stabilizing ring:SR-16-13; |
| XU120179 INA Slewing Ring Bearings | Mass pillow block:9.13 kg; R1:38.1 mm; N1:19.05 mm; End plug (suffix Y):EPR 3; P120°:13.3 kN; RG:1/8 NPT; A1:69.85 mm; Cap bolt, SAE grade:8; R2:17.462 mm; Cap bolt:2 x 1/2-13 UNC; Bearing limiting speed:7000 r/min; Initial grease fill:39.69 g; P180°:14.7 kN; H:134.938 mm; Stabilizing ring:SR-11-9; h:32.544 mm; Housing:SAF 609; P90°:20.9 kN; L:244.475 mm; Da:100 mm; |